Manx SA7x Guide d'installation

SA7x/6000 Cabinet SeriesUpgrade Installation GuideOrder Number EK–SA7CK–IN–003Digital Equipment CorporationMaynard, Massachusetts

1.2 SA70–CK Parts ListThe SA70–CK kit contents are listed in Table 1–2. Be sure all contents of the kit are presentbefore starting the installation pr

Table 1–2 (Cont.): SA70–CK Kit Parts ListPart Number Description Quantity90–08264–00 Cable mount 190–07087–00 5/8-inch cable clamp 290–00063–41 10–32

1.3 Unpacking the SA70–LK/MK, SA71–NK/PK, SA72–NK/PK, andSA73–NK/PK OptionsThe SA7x options are shipped in a packaging box. The SA70–CK kit are shippe

Figure 1–1: Unpacking the SA70 EnclosureCONTAINERDESICCANTSHIPPINGSTRAPSCXO-2439B_SMANUALS ANDMOUNTINGHARDWARESA7xENCLOSURE1–6 SA70–CK and Upgrade Kit

Chapter 2Safety Precautions2.1 IntroductionThis chapter discusses hazards and safety precautions that the Digital Services engineershould be aware of

Chapter 3Installing the SA70–CK Kit3.1 IntroductionThis chapter describes the following:• How to power down the VAX 6000-series processor cabinet• How

Figure 3–1: Front View of the VAX 6000-Series Processor CabinetCXO-2787AFRONT DOORKEY PINFRONT DOORKEY PINGROUNDSTRAPOCP ACCESSPANEL3–2 Installing the

Figure 3–2: Rear View of the VAX 6000-Series Processor CabinetCXO-2788AESDPACKETH405 POWERCONTROLLERPOWERCONTROLLERSCREWS (6)ESDGROUNDLUGInstalling th

3.2 Powering Down the CabinetThe VAX 6000-series processor cabinets use H405 power controllers. To remove power fromthe cabinet, use the following pro

Figure 3–3: Cabinet Control Panel and Power ControllerStandbyEnableSecureAuto StartBatteryRestartRunFaultUpdateHaltONOFF0CONTROL PANELH405-E OR -FPOWE

First Revision, October 1989Second Revision, April 1992Third Revision, September 1992The information in this document is subject to change without not

If the H405–E/F revision level is:a. Revision H07 or above for H405–E, Revision J07 or above for H405–F:• The H405–E/F power controller contains unswi

4. Swing the top of the door away from the cabinet, lift the bottom of the door up and outof the bottom hinge, and set the door aside.To install the n

3.6.2 Moving the ESD StrapUse the following procedure to move and reattach the ESD strap:1. Locate the front ESD packet, shown in Figure 3–4. The pack

3.6.3 Installing the 74-39405-01 BeCu Spring ClipsUse the following procedure to install beryllium copper (BeCu) spring clips:1. Install one BeCu spri

Figure 3–5: Installing BeCu Spring ClipsSPRINGCLIPSLOCATIONSPRINGCLIPSLOCATIONCABINETUPRIGHTCABINETBASESPRINGCLIPS.50CXO-2795A.50CABINETCENTERDIVIDER.

5. Go to the front of the cabinet. Install washer (90–06637–00) and shoulder screw (12–24007–02) into the front center hole of the guide rail plate as

Figure 3–6: Installing the Guide Rail Plate AssemblySCREW12-24007-02WASHER90-06637-00GUIDE RAILPLATE ASSEMBLYBOTTOMREARSTANDOFFWASHER (3)90-06637-00SC

Figure 3–7: Chassis Retainer Brackets and Shim OrientationGUIDE RAILPLATE ASSEMBLYSCREW12-24007-01SCREW12-24007-01WASHER90-06637-00WASHER90-06637-00TO

12. Install the washer (90–06637–00) and shoulder screw (12–24007–01) through the bottomhole of the chassis retaining bracket and into the middle hole

Figure 3–8: Front Clamping AssemblyTOPCHASSISRETAININGBRACKETBOTTOMCHASSISRETAININGBRACKETCXO-2794BTOPSHIMRAIL CHASSISASSEMBLYGUIDERAILASSEMBLYCABINET

ContentsPreface viiChapter 1 SA70–CK and Upgrade Kits1.1 Introduction . ...1–11.2 SA70–CK Parts

3. Lift and move the SA7x enclosure into place using a Digital lifting device (FC–10117–AC).WARNINGIf a lifting device is not available, two people ar

Figure 3–9: Rear Clamping AssemblySA7xENCLOSURECHASSISHOLE 2 OFMOUNTINGSPACERAILCHASSISASSEMBLYCXO-2807B_SCABINETREARVERTICALUPRIGHTREAR RETAINERCHASS

Figure 3–10: Installing the Digital MedallionFRONTCOVERUnit SelectRunRunFault/Fault/Set No.Set No.Ready ReadyUnit No.Unit No.Write WriteProtect Protec

Figure 3–11: Repositioning Transition Board 1CXO-2797ATRANSITIONBOARD 1(BEHIND FRAME)SLOTTEDHOLESLOTTEDHOLEHOLE FORTB1 RIGHTPOSITIONHOLE FORTB1 LEFTPO

2. Route the SA7x enclosure power cord through the clamp attached to the cable manage-ment guide as shown in Figure 3–12.3. Plug the male end of the S

Figure 3–12: Attaching a Single SDI Cable to the SA7x and KDB50/KDM70 I/O BulkheadLRLFRFRRRFGREYSHORTLRYELLOWLONGRRBLACKLONGLFREDSHORTPORT A I/O CABLE

Figure 3–13: Attaching a Second SDI Cable to the SA7x and KDB50/KDM70 I/O BulkheadLRLRLFLFRFRFRRRRRFGREYSHORTLRYELLOWLONGRRBLACKLONGLFREDSHORTPORT A I

Figure 3–14: Cabinet Control Panel and Power ControllerStandbyEnableSecureAuto StartBatteryRestartRunFaultUpdateHaltONOFF0CONTROL PANELH405-E OR -FPOW

Chapter 4SA7x Controls and IndicatorsThis chapter describes the controls and indicators on the front and rear panels of the SA7xenclosure.4.1 SA7x Fro

Figure 4–1: Front Panel View of the SA7x EnclosureFRONTCOVERLEFTFRONTLEFTREARRIGHTREARRIGHTFRONTDRIVE POWER SWITCHESCXO-2447A_SRIGHTREARRIGHTFRONTLEFT

3.7.2 Installing the Rear Clamping Assembly ...3–163.7.3 Installing the Digital Medallion ...

While a drive is powering up and spinning up, the controls and indicators have slightlymodified meanings, as described in Section 5.2.Each control set

Table 4–1 (Cont.): Front Panel Controls and IndicatorsPressing this Switch Performs this Function Illuminates this IndicatorRun switch Spins up the dr

4.2 SA7x Rear Panel Controls and IndicatorsAll rear panel controls and indicators are located on the power supply chassis, as shown inFigure 4–2.Figur

4.2.1 Master On/Off SwitchThe master on/off rocker switch for the SA7x enclosure is located in the center of the rearpanel. Setting the switch to 1 ap

Chapter 5Powering Up the SA7x EnclosureThis chapter explains how to use the SA7x enclosure and drives and how to set the unitnumber.5.1 Powering Up th

The disk drive starts the drive’s internal power-on diagnostics. All indicator lightsilluminate for about 8 seconds. Then:a. If the drive completes th

5.4 Setting the Unit NumberThe unit number for any drive can be set at the operator control panel. This is the numberby which the drive is known to th

Chapter 6Installing RA7x Disk DrivesThis chapter describes how to install additional RA7x disk drives into SA7x enclosures thatare not fully populated

2. Set the master on/off switch to 0. This removes power to the enclosure.6.3 Installing the RA7x Disk DriveTo install additional drives, remove the f

Figure 6–1: Installing Add-On RA7x Disk DrivesSHOE PLATERETAINING CLIPSHOE PLATERA7x DISK DRIVEREAR PANELSHOE PLATEGUIDEINTERNALSDI CABLESCXO-3442A_SL

3–11 Repositioning Transition Board 1 ...3–193–12 Attaching a Single SDI Cable to the SA7x and KDB50/KDM70 I/O Bulkhea

Index70–27273–01See SA70–CKAAdd-on kitSee SA7x enclosure add-on kitAir flow, 5–1BBeCu spring clipsinstalling, 3–9Beryllium copper spring clipsSee BeCu

Indicators (cont’d)functions, 4–4, 4–5rear panel, 4–5types, 4–1, 4–4KKDB50/KDM70 disk controller I/O bulkhead, 3–20LLine voltage select switch, 4–4, 4

VAX 6000-series processor cabinet (cont’d)safety precautions, 2–1, 3–1Voltage select switchSee Line voltage select switchWWrite Protect indicator, 4–4

PrefaceThis manual describes:• How to unpack the SA70–LK/MK, SA71–NK/PK, SA72–NK/PK, or the SA73–NK/PKoptions.• Safety precautions for Digital Service

ScopeGeneral information about the VAX 6000-series processor cabinet and field acceptanceprocedures is not contained in this manual. Refer to documenta

Chapter 1SA70–CK and Upgrade Kits1.1 IntroductionThis chapter a brief description and parts list of the SA7x options and related upgradekits available

Table 1–1 (Cont.): SA7x Options for VAX 6000 Embedded StorageOption DescriptionSA72-PK SA72-JK Storage Enclosure with 4 GB (4 RA72) Disk Storage capac